If your dirt bike stalls whenever you try to put it in gear, don’t worry—you’re not alone. This is a common problem that a lot of dirt bikers experience. In this article, we’ll explain why your dirt bike stalls when you try to put it in gear, and we’ll give you some tips on how to fix the issue.

Why Dirt Bike Stalls When Put In Gear?

There are a few reasons why your dirt bike might stall when you put it into gear. One possibility is that the clutch isn’t engaged properly. If the clutch isn’t fully disengaged, it can cause the engine to stall. Another possibility is that the clutch cable is too tight. If the cable is too tight, it won’t allow the clutch to engage fully, which can also cause the engine to stall. Finally, it’s possible that the engine simply isn’t getting enough gas. If the carburetor isn’t set correctly, the engine may not be getting enough fuel, which will cause it to stall. If your dirt bike stalls when you put it into gear, check to see if the clutch is engaged properly, the clutch cable is too tight, or if the carburetor needs to be adjusted.

Related: Why do dirt bike turn off when put in the gear?

We are not leaving you yet, we will discuss all these possible reasons in detail and will provide you with a quick fix for each of them:

1. Clutch Issue:

The first major issue is the clutch not being engaged properly and can be adjusted by following these simple steps:

1. Check if the cable is too tight: If you think that the clutch cable might be too tight, try loosening it a bit. To do this, find the adjusting nut on the cable and turn it counter clockwise. You should only need to turn it a quarter of a turn or so. Once you’ve done this, try putting the bike into gear again. If it doesn’t stall, then the cable was too tight and that was the cause of the problem.
2. Check if the clutch needs to be adjusted: If loosening the clutch cable doesn’t fix the problem, then you might need to adjust the clutch itself. To do this, find the adjusting screw on the clutch lever and turn it clockwise. Again, you should only need to turn it a quarter of a turn or so. Once you’ve done this, try putting the bike into gear again. If it doesn’t stall, then the clutch was the cause of the problem.

2. Carburetor Issue:

If you think that the carburetor might be the cause of the problem, there are a few things you can do to fix it. First, check the fuel level and make sure that there’s enough gas in the tank. If there isn’t, then fill it up and try again. If the fuel level is fine, then the next thing to check is the carburetor itself. Make sure that all of the jets are clean and that the carburetor is adjusted correctly. You can find more information on how to do this in your dirt bike’s service manual.

3. Dirty Air Filter:

The next thing to check is the air filter. If it’s dirty, it can restrict airflow and cause the engine to stall. To clean the air filter, simply remove it from the bike and wash it with soap and water. Once it’s clean, dry it off and put it back on the bike.

The air filter is responsible for providing enough air to the engine, and if it’s dirty, the engine will stall.

4. Spark Plug Issue:

If the spark plug is fouled or damaged, it can cause the engine to stall. To check the spark plug, remove it from the bike and inspect it. If it’s covered in soot or oil, then it needs to be cleaned. To clean it, simply use a wire brush to remove any debris. Once it’s clean, put it back in the bike and try again.

5. Low Oil Level:

If the oil level is low, it can cause the engine to stall. To check the oil level, simply remove the dipstick from the oil tank and see where the oil level is. If it’s below the “full” line, then you need to add more oil.

6. Fuel Line Issue:

If the fuel line is clogged, it can restrict fuel flow to the engine and cause it to stall. To check the fuel line, simply remove it from the bike and inspect it. If it’s clogged, then you need to clean it out. To do this, simply use a wire brush to remove any debris. Once it’s clean, put it back in the bike and try again.

Sometimes fuel line gets leaked, and because of that, the engine will stall.

Tips to Avoid It in The Future

Below is the seven steps checklist to avoid stalls in the future:

1. Check the air filter regularly and clean it when necessary.
2. Check the spark plug regularly and replace it if necessary.
3. Check the oil level regularly and add oil when necessary.
4. Check the fuel line regularly and clean it when necessary.
5. Inspect the carburetor regularly and clean it when necessary.
6. Adjust the clutch cable regularly to prevent it from getting too tight.
7. Inspect the clutch regularly and adjust it when necessary.

By following these simple tips, you can avoid most of the common causes of engine stalls and keep your bike running smoothly.

Frequently Asked Questions

Does Stalling Damage Dirt Bike Engine?

When you stall a motorcycle engine, it’s not like slamming on the brakes of a car. You’re not going to stress or damage the engine by stalling it. In fact, stalling is simply when the air-fuel mixture in the cylinders isn’t combusting. The engine still has plenty of oil lubricating it, so there’s no risk of damaging it from stalling. So don’t worry about stalling your motorcycle engine, it’s not going to do any damage. Just be prepared for some surprised looks from onlookers who think you’ve stalled out and are in for a long walk home.

What Happens If You Keep Stalling A Dirt Bike?

If you keep stalling your dirt bike, it’s not going to do any damage to the engine. However, it can be frustrating, especially if you’re trying to ride in a specific area or get to a certain point. If you find that you’re constantly stalling, then you need to figure out what’s causing it. Check the air filter, spark plugs, and fuel line to see if they’re clean. If they’re not, then clean them and try again. Also, make sure that the carburetor is adjusted correctly. You can find more information on how to do this in your dirt bike’s service manual.

Conclusion

Stalling is a common issue that all dirt bike riders face at some point. However, it’s usually not a big deal and can be easily fixed. If you find that you’re constantly stalling, then take a look at the air filter, spark plugs, and fuel line to see if they’re clean. Also, make sure that the carburetor is adjusted correctly. By following these simple tips, you can avoid most of the common causes of engine stalls and keep your bike running smoothly.